Algo 8028 user guide
.
.
Download / Read Online Algo 8028 user guide
.
.
.

.
Top element. ALGO 8028 SIP Doorphone 8028 SIP Doorphone FW Version 2. ALGO 8028 SIP Doorphone Table of Contents IMPORTANT SAFETY INFORMATION . ABOUT THE ALGO 8028 SIP DOORPHONE . YPICAL PPLICATIONS FOR UXILIARY NPUTS AND UTPUTS Cancel Ring When Door Opened . INSTALLATION When the Doorphone Controller is connected to wiring that exits the building, there is potential risk of lightning induced electrical surges or high voltages from fault conditions. The 8028 Doorphone includes a Control Unit, Door Station, and Power Supply. Door Station located outdoors and the Control Unit in a dry indoor location. Press the call button on the Door Station. A recorded voice will speak the IP Address of the device. Press the call button on the Door Station, then answer to communicate with the Door Station. ALGO 8028 SIP Doorphone Door Station Installation The Door Station, provided with the 8028 Doorphone kit, is weather protected for outdoor installation. However if network cabling extends beyond the perimeter of the building then adequate lightning protection is required to protect the cabling and network switch from lightning surges. ALGO 8028 SIP Doorphone Door or Gate Control Basics Control contacts are provided from the Doorphone Controller and are typically used for door strike activation or gate control. Maximum switching capability of the 8028 door control contacts is 1 A 30 V. ALGO 8028 SIP Doorphone Wiring Connections Door Control Relay Normally Open V 0. ALGO 8028 SIP Doorphone Auxiliary Dry Contact Outputs Both the Doorphone Controller and Door Station provide a dry contact output for connection to auxiliary devices. Maximum switching capacity is 30 V 50 mA. Open Code is pressed from the telephone keypad during a call with the 8028 intercom. After boot up the red call button will turn on and the Doorphone will have obtained an IP address. If there is no DHCP server the 8028 SIP Doorphone will default to the static IP address 192. Before the 8028 is configured, the call button on the Door Station can be pressed to play the IP address over the speaker. Status page will be available before and after log on. SIP Server Name or IP Address Extension The phone number that the 8028 registers with the SIP Server. Authentication ID ID used to register the device on the SIP Server. May also be called Username for some SIP servers and in some cases may be the same as the SIP extension. ALGO 8028 SIP Doorphone Authentication Password SIP password provided by the system administrator for the SIP account. Dialing Extensions Phone number to be dialed when the Call button on the door station is pressed. This can also be a Hunt Group number. Ensure that voice mail is not reached. Ringback Tone Allow audible ringback tone to be played on the doorphone speaker until the call is answered. DTMF code that can be used to unlock the door for a brief period of time. DTMF code that will lock the door again when it is latched open. Door Unlock Tone A sound can be played when a door is unlocked, to create awareness. When selected, DHCP will automatically configure IP addresses for each 8028 SIP Doorphone on the network. ALGO 8028 SIP Doorphone VLAN ID Specifies the VLAN to which the Ethernet frame belongs. VLAN to which the Ethernet frame belongs. The hexadecimal values of 0x000 and 0xFFF are reserved. All other values may be used as VLAN identifiers, allowing up to 4094 VLANs. Admin Password Password to log into the 8028 SIP Doorphone web interface. You should change the default password algo in order to secure the device on the network. If you have forgotten your password, you will. Log Size Consult Algo technical support. Network time is used for logging events into memory for troubleshooting. NTP Time Server Allows the 8028 to synchronize to an external time server. For example, 8028 SIP Doorphone configuration files can be automatically downloaded from a TFTP server using DHCP Option 66. TFTP boot server address to the DHCP client to boot from. Provisioning server If using a generic configuration file, extensions and credentials have to be entered manually once the 8028 SIP Doorphone has automatically downloaded the configuration file. F Algo Communication Products Ltd. Since all the necessary settings can be included in this file, the 8028 will be ready to work immediately after the configuration file is downloaded. The MAC address of each 8028 SIP Doorphone can be found on the back label of the unit. Call Answer Inbound Call Allow the 8028 to auto answer an inbound call. By default, this functionality is activated. Answer Tone An optional beep tone can be played over the speaker when the Door Station answers an inbound call. The call will be terminated once the maximum time is reached. Only change if instructed otherwise. If primary server is unreachable the 8028 will attempt to register with the backup servers. If enabled, the 8028 will always attempt to register with the highest priority server. SIP Doorphone will attempt to regi filexlib.
.
Algo 8028 manualidades
Algo 8028 handboek
Algo 8028 bedienungsanleitung
Algo 8028 service manual
Algo 8028 handleiding